Home › DrewsBrews › Comments
Site Links
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Badges
Please review the site Rules, Terms of Service, and Privacy Policy at your convenience. Rules, TOS, Privacy
Get familiar with the reaction system: Introducing the Reaction System
DrewsBrews
About
- Username
- DrewsBrews
- Joined
- Visits
- 4,155
- Last Active
- Roles
- Veteran
- Points
- 1,571
- Invited by
- Bryan@MAC
- 24
- Badges
Comments
-
You guys are the best. Thanks for the input! Sounds like if it does somehow mess with an amp/crossover negatively it would either be a fluke, or something else is wrong. @4thtry Yeah thinking of using PM180 sealed in 5liters. F6 estimated ~109hz.…
-
Menards: (Image) Typical thick glass bar/restaurant style. Stock you home pub then buy shelving boards with the rebate!
-
(Quote) Dang that's a nice simple idea.. Beats the hell out of my sheet of paper folded into thirds for 30/60deg and in half again for 15/45deg. Then eyeballing it ;) .
-
Ooh yeah the SB26ADC for $35.
-
Happy Bday man
-
At some point I want to do a build with OSB. https://ibuildit.ca/projects/making-a-powered-sub-woofer/
-
I have ordered from Solen once. Don't remember the carrier, but normal shipping charge and no other fees after the fact.
-
For the low voltage kit? The suggested replacement caps are taller and the tops contact the case top, but otherwise seems to fit fine.
-
Interesting about the magnet capping the pole piece. Does it have an abnormally large xmax or sensitivity for its size?
-
(Image) Some quick woops for funzies. I didn't get all the measurements I need/want so I'll remeasure later. Interesting to see that 6-7khz trough is gone and instead is a much smaller deep suckout at 6k (pre smoothing). Probably need some off …
-
Had a random thought while perusing the site.. MTM with JDT tweeter and E5s? A pair of E5s models pretty nice in <.5cf ported.
-
Not to muddy up the thread, but after some trial and error I was able to get ahold of someone at ESS. I sent my measurements along with info on the measurement setup. They offered to send out a replacement tweeter, or diaphragm with instruction on …
-
(Quote) I was going to try some 1/2" felt pressed in so it hugs the angled side contour, bent at the center close to the diaphragm.
-
Kindof reminds me of the inverse of an issue zaph had on his earlier measurements... The fundamental on the graphs would exhibit valleys at intervals on his distortion measurements.
-
@PWRRYD any interest in experimenting with side wing/s to get some bottom end back on the tc9?
-
Oof, I have yet to muster up the gumption to try a standard 90deg miter on a box let alone doing it 8x on one enclosure. Then the glueup I'm envisioning something similar to herding cats.
-
(Quote) Yeah seems some folks forget this is a hobby and different people have different lines between leisure and work. For me if it gets too complicated I stop having fun. Then it's like I'm still at work. And I'm a work to live, not live to wo…
-
I hear alot of cheaper premade guac may not have much avocado. There is a gourd that has a very similar color, consistency and flavor.
-
I was forced off PCD too a while ago. I switched to WinPCD. It's acoustic offset method is nice and easy to work with for getting reasonable results with only a handfull of measurements. Guys get some awesome results with ViituixCAD but they need…
-
(Quote) That's gotta be what they use in Chipotle guac. That is the best damn guac I've had and I just can't quite put my finger on why. My BP might be lower if I could get ESS to respond to an email. I'll probably try to call tomorrow on my lunch…
-
I wouldn't worry about the hump at all. in a smaller space it will be punchy. In a big space it will reinforce and keep it from seeming anemic.
-
Have you seen how folks can try to use a thickness planer as a jointer by shimming the piece against another flat board? I'm wondering if you could do something similar on the table saw. Attach the enclosure shell (curved side down) on a sacrifici…
-
I enjoyed medium heat stuff. But in the last year it seems my insides dont like it anymore.
-
(Quote) Continued working with battery drill and flashlight on one of the speakers. Predrilled the screw holes and trimmed some thin hobby sheet foam as a giant gasket. Front is now buttoned up enough for testing. Just need power back to run some …
-
Drilled screw holes in the baffle board and screwed one of the drivers in. Then a car hit a nearby power pole and probably out of power the rest of the day.
-
I just think it is BS that I can spend that much and they are perfectly fine to let me pay $72 shipping to send me junk (was the cheapest shipping option). Reading their return and refund policy I can see I've made a big mistake. They have zero sk…
-
(Image) Not exactly happy with this. I expected better quality control for the prices these command.
-
(Quote) "Ran when parked" Interesting to see the progression of sophistication in diaphragm design. I initially thought the mesh was some sort of grill. Now I'm thinking it is likely fiberglass that is glued to the tips of the pleats to …
-
I understood yours are older versions. When searching around online I thought I had seen plots that look pretty identical to the blue line. With the typical 800hz resonance. The green line.. not so much. I just don't want to be dealing with a fa…
-
hmm (Image) I don't realy have experience with AMTs yet. Please someone tell me this is nothing to worry about because I'm on the edge of being rather annoyed.